Beskrivelse

KOMMER FOR SALG – FORHÅNDSBESTILLING!

go-e lader Gemini

Den intelligente veggboksen for hjemme eller på firmaparkeringen. Intuitivt design og en rekke sikkerhetsfunksjoner kombinert med smarte bekvemmelighetsfunksjoner som også oppmuntrer til bærekraftig lading. Ladeeffekt fra 1,4 kW til 22 kW. 1-fase eller 3-fase lading og har innebygget jordfeil vern type B. Den er utrolig liten Kun 155x260x110 mm!

Laderen har det meste av funksjoner (ikke 4G) og er produsert i Østerike. Laderen passer til alt i fra borettslag, bedrifter, hjemme eller hytta. Den kan også brukes sammen med Monta app og gir stor grad av fleksibilitet.

Link til DSB:

https://www.dsb.no/lover/elektriske-anlegg-og-elektrisk-utstyr/tema/elbil—lading-og-sikkerhet/

 

Product specifications:

• Dimensions: approx. 15,5 x 26 x 11 cm
• Weight: approx. 2.34 kg
• Connection cable: 1.8 m, 5 x 6 mm² for permanent connection (Typ H07BQ-F)
• Nominal voltage: 230/240 V (single-phase) / 400/415 V (three-phase)
• Mains frequency: 50 Hz
• Power grid types: TT/TN/IT
• Standby power: 3.1W (LEDs switched off) to 5.2 W (LEDs bright)
• RFID: 13.56 MHz
• WiFi: 802.11b/g/n 2.4GHz / frequency band 2412-2472Mhz

Permissible ambient conditions:

• Installation site: indoors and outdoors, without direct sunlight
• Operating temperature: -25 °C to + 40 °C
• Storage temperature: -40 °C to + 85 °C
• Average temperature in 24 hours: maximum 35 °C
• Altitude: maximum 2,000 m above sea level
• Relative humidity: not more than 95 % (non-condensing)
• Impact resistance: IK08

Charging Capacity:

• Maximum charging power 7,4 kW (32 A 1-phase)
• Ampere and status Display: readable via LED ring and app
• Adjusting charging power: by button and app
• Charging power adjustable between 1.4 kW and 22 kW (via the charging current in 1 ampere steps between 6 A and 32 A) depending on the number of phases of the car‘s onboard charger:
  • Single-phase charging car: 1.4 kW to 7.4 kW (country-specific limitations need to be observed)

Connection to vehicle:

• Type 2 socket (EN 62196-2) with mechanical locking device (own type 2 cable required, available as accessory)
• vehicles with type 1 can be charged with adapter cable type 2 to type 1 (available as accessories)

Safety functions:

• RCD protection module with DC current detection: 20 mA AC, 6 mA DC
• Protection class: I
• Pollution degree: II
• Anti-theft device: charging cable locking device
• RFID access control: one learned RFID chip included
• Input voltage: phase and voltage testing
• Switching functions: testing of the switching functions
• Ground check: for TT, TN grids (deactivatable ground check for IT grid – Norway mode)
• Current sensor: 1-phase
• Grid-serving control: two data cables for connection to ripple control receiver
• IP55 protected against dirt and water, suitable for permanent outdoor operation
• go-e network operator API: for authorised access by the electricity grid operator to the go-e Charger for grid-serving power control
• Modbus TCP: e.g. for grid-serving power control by the electricity grid Operator

App and connectivity:

• Local (WiFi hotspot) or worlwide** (WiFi) controlling and monitoring
• Adjustment/check of the charge (voltage, current, power, energy)
• Adjusting the current level in 1 ampere steps
• Start/stop function
• Management of RFID chips/cards (up to 10 users per charger) / Access control (RFID/App)
• Scheduler
• Electricity meter (total kWh and total amount per RFID chip)
• kWh limit mode / Eco mode** / Planned charge mode**
• Push notifications**
• Cable unlock functions
• Flexible energy tariffs with intelligent charging management**/***
• Static load balancing**
• Photovoltaic connection via open API interface (programming required)**
• OCPP 1.6**
• LED Adjustment
• Management of the charging levels via button on the charging Station
• Updateable for later functions (Smart home, etc.)**
• Automatic unlocking of the charging cable in the event of a power failure
• 1-/3-phase switching via app – even during the charging process
• Synchronisation of charging processes with the cloud and display of the past charging processes**
• Documented public API interfaces: HTTP, MQTT, Modbus TCP